Новинки

2019-05-14Противопожарные-клапаны-FDA2-с-инспекционным-люкoм

The FDA2-12 round fire dampers are designed for use in general ventilation systems to seal off smoke and fire between adjacent fire partitions. The fire damper blade remains open under normal operating conditions. It is closed shut automatically in the event of a fire. 

• The fire dampers are classified according to EN 13501-3+A1:2010P,
• The fire resistance was tested as per EN 1366-2:2015,

• The entire manufacturing process meets the requirements of EN 15650:2010.

 BENEFITS:

• The FDA2-12 fire dampers can be installed in horizontal and vertical fire partitions to provide fire resistance of
  EI 120 (ve ho i↔o) S

• Designed for round and rectangular ventilation systems,

• Available dimensions: in the nominal sizes from 160x160 to 1000x500mm or diameter from 200 to 630mm,
• The dampers have an inspection panel,
• Possible use of fire dampers in general ventilation,
• All fire dampers have a torsion spring trip (in version FDA2-12-T) or

• a return-spring actuator coupled with a thermal trip (in version FDA2-12-M).

The fire dampers can be installed in the following partitions: concrete separing floor, concrete wall, solid brick wall, cellular concrete unit wall, gybsum board wall on steel frame.

2019-04-03SMOKE System Bоздуховоды для систем дымоудаления

The system of single-compartment steel, circular smoke extraction ducts in E600 120 (ho) S1500 single fire resistance class is intended to be used in the construction industry in a horizontal system as elements creating a smoke extraction ventilation system or combined ventilation, fulfilling at the same time the functions of general and smoke extraction ventilation, assuming that they serve only the compartment in which they have been installed. Systems serving one fire compartment may be independent systems or may be combined with a collective, multi-compartment system. The main task of the smoke extraction systems is to remove hot gases and smoke from the area covered by the fire in order to facilitate the evacuation of people and to enable the extinguishing action and the evacuation of people from the area at risk, while complying with the criteria of fire and/or smoke tightness specified under conditions of exposure to a temperature of 600°C.

 
SMOKE system single-compartment circular smoke extraction ducts have the following application areas:

• Smoke extraction ducts are designed for single fire compartments,

• The smoke extraction ducts are available in diameter range is from Ø100 to Ø1000mm,
• The maximum temperature of the fire gases discharged through the SMOKE system ducts is 600 °C,
• Individual duct sections and ventilation fittings of SMOKE system ducts may only be installed horizontally (vertical installation is not permitted),
• The scope of application of smoke extraction ducts includes ventilation systems with operating pressure from -1500 Pa to +500 Pa.

2019-03-21FLX-REKU - The complete air distribution system in a brand NEW version

The smart solution for air distribution - FLX-REKU system: 

The FLX-REKU air distribution ductwork consists of ventilation semi-rigid ducts, distribution and plenum boxes, ventilation dampers and other elements that, together with a heat recovery unit, constitute a complete mechanical ventilation system with heat recovery (MVHR). The FLX-REKU system is a great solution when high durability and flexibility are required. The high circumferential rigidity allows burying the ducts in concrete.

 BENEFITS:

• Aesthetics of the installation - high durability and mechanical strength allows for assembly in a concrete screed in the ceiling or in the insulation layer,
• Small dimensions and a unique structure allow installing FLX ducts under the ceiling, on walls and laid on floors,
• The minimum number of joints ensures minimal pressure loss,
• The antimicrobial lining in FLXHDPE-A ducting contains silver ions,
• Quick and easy assembly - the offer includes all necessary couplers and mounting accessories!

• Guaranteed airtight installation - connections with EPDM seals,

We have expanded the range of FLX-REKU system products with silencers, offsets and UPgraded the design of plenum and distribution boxes!!

2019-02-19Meet us at ISH 2019

We would like to invite you to visit ISH 2019 which will take place in Frankurt on 11-15 March. 2019. Let's meet at ISH 2019 at Alnor's stand no C31 in Hall 8.0.

We'll be expecting You from 11. - 14.3.2019 (Monday to Thursday): 9 a.m. to 6 p.m, and on 15.3.2019 (Friday - Public day): 9 a.m. to 5 p.m.

Don't miss opportunity for talk about our new products which can make your offer more attractive, amongst them smoke extraction system, new models of fire dampers and VAV and CAV regulators. .

2019-01-02Рейтинг Газель бизнеса 2018

Рейтинг Газели бизнеса, это рейтинг наиболее динамично развивающихся малых и средних компаний. С точки зрения газеты „Пульс бизнеса» (”Puls Biznesu”), Газель – это компания среднего размера, которая благодаря очень динамичному развитию, великолепно справляется со своими заданиями, даже в окружении значительно более крупных конкурентов. Рейтинги Газели бизнеса проводятся ежегодно экономическими газетами, принадлежащими шведской группе Bonnier Press Group. Кроме «Пульса Бизнеса» ("Puls Biznesu"), такой перечень составляют аналогичные журналы из Швеции, Дании, Австрии, Латвии, России, Эстонии и Словении. Критерии выбора Газелей в конкретных странах зависят от местных экономических условий, однако, цель везде одна: продвижение малого и среднего бизнеса.

2018-11-19Meet us BIG 5 Dubai 2018

Join ALNOR team at the largest fair trade in the Middle East - Big 5 in Dubai between 26 - 29 November 2018.

We are exhibiting with both our standard products like fittings and silencers as well as brand new ones - round and square fire dampers, VAV and CAV volume regulators.

You are very welcome in Hall Zabeel 5, booth Z5 D70 to talk with us about cooperation.

2018-09-04Meet us at SMM 2018

Join ALNOR team at the largest fair trade for Marine industry in Germany SMM 2018 in Hamburg between 4-7.09.2018. 

We're presenting 5 complete ventilation systems for marine applications: pre-insulated ductwork with 10, 16 and 25mm insulation, air insulate ductwork and aluminium system, as well as offshore ventilation system made of stainless steel.

You are very welcome in Hall B5, booth B5.516 to talk with us about cooperation.

2018-07-18Вихревые диффузоры

Потолочные вихревые диффузоры GCR:

• изготовлены из листовой стали и покрашены порошковой краской белого цвета (RAL 9010),
• диффузоры обеспечивают смешивание свежего воздушного потока с комнатным воздухом,
• предназначенные для помещений высотой до 4 м, например, в общественных помещениях, таких как офисы, спорткомплексы, гостиницы, офисы, магазины, рестораны, кафе,
• типы соединения:с соединительным ниппелем или с муфтой воздуховода, с перфорированной крышкой или без нее,
• широкий диапазон размеров: 125 - 400 мм.

Download the pdf file for Swirl Diffusers GCR

These and other products for ventilation and heat recovery can be found in the PRODUCTS section 

2018-06-07DAT-AKU - клапан-глушитель для каналов воздуховода

клапан-глушитель для каналов воздуховода:

• made of polyurethane foam,
• regulation of air flow and noise suppression in the ventilation system,
• thickness: 50 mm or 75 mm,
• non-combustible material (class B2 according to DIN4102-1),
• a wide range of sizes,
• the possibility of using several dampers at a time in the ventilation duct.
  
  

2018-06-07Over 1000 products in one place!

Get to know our Product Range – Check our Product Overview! On 44 pages we’ve shown over 1000 products, described more than 10 ventilation systems and reviewed all our certificates, technical approvals as well as selection software that supports our clients. 

Examples of our ventilation systems:

1. The SPIRAL-System is a proven system of quick-coupled spiral ducts and fittings provided with factory-installed EPDM gaskets. The gaskets provide leak-proof and durable joints between SPIRAL®system components. The system components are available in a full range of diameters from Ø80 to Ø1250 mm. SPIRAL system meets the requirements of PN-EN 12237 for air tightness class D (Certificate no. 0103/07).
2. Components of the FIX-System suspension are made from galvanized steel or stainless steel and they meet the requirements of the BRI (ITB) Technical Recommendation no. RT ITB - 1112/2008 Includes: EQVS, EQZS, EQLS, CLR, CLRL, TKN, KLQ, PG, TK, LDB, PB.
3. Roof installation accessories are a range of fixtures and tools for easy and safe suspension of round and square ventilation ducts. Roof installation accessories are a range of modular roof support kits and roof feet, as well as other accessories that make the assembly easy and fast. Sets of roof supports can be used on flat roofs and slightly sloped roof. Roof support kit consist of perfectly matched elements - roof feet, sections of channel, screws, nuts, etc.
4. FLX-REKU is a complete ventilation system which comprises ventilation ducts, plenum boxes, air dampers and other components for building ventilation solutions with heat-recovery units. The system comes very handy when heavy-duty and flexible ducts are required. The high circumferential rigidity allows burying the ducts in concrete.
5. The EPP duct system is made of expanded polypropylene. The system has a number of design and installation advantages: low weight, quick installation (no additional connectors or screws required), no additional insulation is required since the material itself is already an insulator, easy to cut using hand tools, no thermal bridges. Thermal conductivity: λ=0.039 [W / m * k].
6. SQUER-System - rectangular ducts and fittings.
7. The IZOL®system is a registered tradename of pre-insulated ventilation ducts and fittings for indoor and outdoor systems. All system components are provided with inner and outer steel sheet cladding, and a thermal-insulation layer in between. The nominal diameter range of 100-500 mm always refers to the inner diameter of ducts and fittings. There are 3 types of insulation  available: 25 / 50 / 100 mm.
8. Ducts and fittings insulated with rubber foam Fovent®system. The insulation made of rubber mat is available in 4 sizes: 9, 13, 19 and 25 mm.
9. Insulated fittings IZOL-SAFE System designated for marine applications. Bend with air-insulation and duct with wool based insulation.
10. OFF-SHORE ventilation ducts and fitting - Circular ducts and fittings made of galvanized metal sheets, stainless steel 1.4404, wall thickness in stainless steel fittings from 0,8 up to 1,25 mm depending on diameterr. Swelling gasket for high temperatures purposes.
11. Ventilation systems made of plastics are widely used in many areas and sectors where the conventional materials, such as plated steel or stainless steel become insufficient due to their limitations. Plastics have traditionally been used in laboratories, chemical industry or spaces of high purity grade.
12. TRANS-Quick is a modern clamp-together ducting system intended for industrial dust extraction. Quick assembly and disassembly, using pull rings to connect components - which can be reused and reassembled.Ducts and fittings are manufactured from galvanised steel sheet 0.7 and 0.9 mm in thickness using butt welding method, components are joined with clamps equipped with a gasket.
13. Circular smoke extraction ducts and fittings SMOKE-SYSTEM.

In our product offer You can also find:

• Heat recovery unit
• Filters prevent contaminants from flowing with the air supplied into rooms and ventilation ductwork.
• Valves and ventilation grillse
• Ventilation duct silencers
• Ventilation dampers, vav flow regulatores and actuators
• Duct heaters
• Access doors 
• Duct fans
• Roof hoods and cowls
• Fire dampers and valves

Moreover, our products are tested and certified by:

RISE - Research Institutes of Sweden AB Certification (former SITAC)
Air Tightness Certificate for Ventilation Ductwork System - air tightness class D according to EN 12237:2003 - round spiral ducts and ductwork fittings with seals.

The Building Information Foundation RTS sr
M1 Cleanliness class for air handling components:

• Ventilation spiral ducts
• Pressed bends, reducers, T-pieces and take-offs
• Segmented bends, reducers, T-pieces, take-offs, male couplings, offsets
• Air dampers: regulating, shut-off, iris, multi blade

TÜV Rheinland Polska
Certificate of production quality:

• Round ventilation ducts and fittings
• Mounting accessories
• Regulating, shut-off, non-return and iris dampers
• Ventilation silencers

Instytut Techniki Budowlanej ITB (The Building Research Institute)
Technical approvals and certificates of constancy of performance

• STRUT assembly system
• Suspended mounting elements
• Flexible ducts - fire classification
• Fire dampers

Passive House Institute
Certificate for HRU-PremAIR-450 heat recovery unit confirming compliance with the highest energy efficiency requirements.

...
and many others.