This manual is intended as a reference book by which qualified installers can install the HRQ-SlimAir and all optional device as well. This device must be used according to its purpose. Make sure you have read and understood the manual before you install and/or use the device. Please be informed that we are constantly working on the development and improvement of our products hence minor differences between this document and your unit are possible.
FLX-REKU oval system is intended for residential mechanical ventilation systems with heat recovery. Ducting is semi-rigid nonmetallic made of HDPE (high-density polyethylene), plenum boxes and distribution boxes comprise of galvanised steel and HDPE connectors.
This manual is intended as a reference book by which qualified installers can install the HRQ-PremAir and all optional device as well. This device must be used according to its purpose. Make sure you have read and understood the manual before you install and/or use the device. Please be informed that we are constantly working on the development and improvement of our products hence minor differences between this document and your unit are possible.
This air filter was designed and developed for purpose of removing air pollutants and therefore providing good and healthy indoor air in residential buildings. Air contamination is defined as various size particle matters (PM) like smog, fine dust, soot, fungal spores, pollen, viruses or bacteria. This filter effectiveness is classified according to EN ISO 16890. This is an electrostatic precipitator which uses electrical current and electromagnetic phenomena. We recommend the airflow at 575 m3/h at most to reach best performance, regarding both filtering efficiency and low pressure drop.
Through readings from CO2 sensors in both zones, the HRQ-2ZONE smart air damper distributes airflow as needed. As a result, the HRQ-2ZONE will direct a greater stream of fresh air towards the zone where the household members are currently residing, as opposed to the second zone, temporarily less used.
The HomEvap adiabatic humidifier is designed for domestic mechanical ventilation systems with a maximum airflow 600 m3/h. Filtered water (Legiosafe®) naturally evaporates on a special matrix, and then the humidified air is distributed to the ventilation duct system and to the connected rooms. The humidification process is regulated by a wireless room controller and a duct sensor. Built-in PTC heater compensates for temperature losses caused by the evaporation process. The housing is made of EPP, while the matrix is made of fiber glass.
The device sets and monitors an indoor HRU. This unit controls the indoor air quality by varying the ventilator speed. The device uses wireless communication (RF) to communicate with the HRU. Capacitive touch buttons on the device allow for changes in settings of the HRU. The liquid crystal display (LCD) or screen of the device shows the actual working state the unit is in. When a malfunction of, or a problem with the HRU occurs, the sceen shows the fault of the system.
Wireless, CO2 sensor measures the dioxide level in the room (PPM). Sensor works as a unit controller and indicates the current status by means of a multicolour LED.
Range: 30 m (inside dwelling, 100 m in open space, additional antenna available).
HRU-WALL is a single alternate flow decentralized (single point) residential heat recovery unit, also called«push&pull» unit, designed to ensure adequate ventilation in enclosed environments without energy losses. It is recommended that two units are installed in pair: when one unit is pulling, the other is pushing. Pair of units can be installed in the same room or in different rooms (i.e. livingroom and bedroom). The unit is suitable for installation on an outside wall.
HRU-WALL-PEG & HRU-WALL-RC-PEG is a single alternate flow decentralized (single point) residential heat recovery unit, also called«push&pull» unit, designed to ensure adequate ventilation in enclosed environments without energy losses. It is recommended that two units are installed in pair: when one unit is pulling, the other is pushing. Pair of units can be installed in the same room or in different rooms (i.e. livingroom and bedroom). The unit is suitable for installation on an outside wall.
HRU-WALL-WI is a decentralized, ductless ventilation unit with heat recovery, intended for residential buildings. Also referred to us “push & pull”, wall-mounted or single-room unit. It is recommended that two units are installed in pair: when one unit is pulling, the other is pushing. Pair of units can be installed in the same room or in different rooms (i.e. living-room and bedroom). The unit is suitable for installation on an outside wall.
A window reveal module for the decentralised heat recovery units - HRU-WALL series. The module is intended for installation in the facade, in the insulation layer, a ventilation grille is mounted on the window reaveal. The window reveal module provides practically invisiable solution for supply/extract ducting. This method of installation will be especially useful during the thermal modernization of the building. The product has a universal layout, the choice of "right-sided" or "left-sided" assembly is made at the construction site. In addition, a slope for possible condensation growth was implemented into the design.The duct is telescopic, which means that the distance from the axis of the HRU to the window reveal can be adjusted in the range of 380-490 mm.